Four modular product families, one engineering team. Compare airflow ranges, casing classes and options — then send us your schedule for a compliant selection within 24 hours.
Every series shares the same casing system, control platform and documentation pack — so you can mix unit types on one project without re-learning the product.
The general-purpose platform: 50 mm double-skin casing with thermal break, EC plug or belt-driven fans, and every coil and filter option available.
Stainless steel or coated interior, flush welds, sloped drain pan and cleanable fan compartment — built for EU GMP Annex 1 and VDI 6022 audits.
Rotary wheel, cross-flow plate or run-around coil, with bypass and frost protection — for projects measured on seasonal efficiency.
Outdoor or rooftop packaged unit with integrated inverter compressor and controls — one crate, one connection, minimal plant room.
Indicative ranges — every unit is configured to the duty, so send us your schedule for an exact selection.
| Parameter | AERO-M Pro | MEDIC-AIR | ECO-RECOV | PACK-DX |
|---|---|---|---|---|
| Airflow range | 2,000 – 60,000 m³/h | 1,000 – 40,000 m³/h | 2,000 – 80,000 m³/h | 3,000 – 30,000 m³/h |
| Casing construction | Double skin 50 mm | Double skin 50 / 60 mm | Double skin 50 mm | Single skin 25 mm |
| Casing strength (EN 1886) | D1 | D1 | D1 | D2 |
| Air leakage class | L1 | L1 | L1 | L2 |
| Thermal transmittance | T2 | T2 | T2 | T3 |
| Thermal bridging | TB2 | TB2 | TB2 | TB3 |
| Filtration | ISO Coarse 60% – ePM1 80% | ePM1 80% + H14 | ISO Coarse 60% – ePM1 80% | ISO Coarse 60% – ePM10 60% |
| Heat recovery | Optional | Optional | Standard | Integrated DX |
| Fan type | EC plug / belt-driven | EC plug | EC plug | EC plug |
These are the four numbers your client or consultant will look for on the specification. Ours are type-tested, not self-declared.
≤ 0.5 W/m²K through the casing panel — the heat you paid for stays in the air stream.
Frame to panel conduction limited, so no cold bridges and no condensation streaks on the casing.
Less than 0.15 l/s·m² at 400 Pa negative pressure — leakage you can ignore in the energy calculation.
Panel deflection under 4 mm/m at design pressure; doors and frames stay sealed under load.
Type-test report for casing mechanical and thermal performance.
Certified airflow, power and recovery performance data.
Coil capacity and recuperator efficiency independently verified.
Machinery Directive 2006/42/EC declaration and technical file.
Annual audits, material traceability, calibrated test equipment.
Hygienic design, cleanability and indoor air quality compliance.
Whether the brief is a GMP Grade B filling line, an operating theatre to DIN 1946-4, a data hall with N+1 redundancy or a commercial retrofit with a tight shaft, the same engineering process applies: read the standard, select the unit, document it.
Casing split to your door and shaft sizes; section lengths in 100 mm steps.
Your preferred fans, motors, dampers, sensors and control brand.
Galvanised, coated, AISI 304 or 316L — matched to the environment.
Free-standing panel or pre-wired controller, Modbus / BACnet / KNX.
There is no minimum. We regularly ship single units for retrofit projects as well as container loads for new builds. Freight cost per unit is lower on consolidated orders, so we always quote both options.
Yes. 400 V / 50 Hz three-phase is standard for European shipments, and we supply Modbus RTU, Modbus TCP, BACnet MS/TP or BACnet IP on the unit controller. 230 V single-phase units are available below 7.5 kW.
We supply the casing type-test report and the certified fan performance data with every quotation. Full Eurovent certification documents are included for the certified ranges.
Standard modular configurations ship in 15 working days. Units with non-standard materials, H14 HEPA sections or third-party components take 25–30 working days. Production only starts after approved drawings.
Regularly. Send the specification clause or the equipment schedule and we mark up compliance line by line, flagging any deviation before you commit — no silent substitutions.
Airflow, static pressure, temperatures. That is enough for us to return a compliant selection, budget price and dimensioned drawings.